Start with a shift you already run
For a replacement truck, send the old specification and describe what the crew would change. A bin lifter that misses a row of municipal bins, a deck that bottoms out under a low car, or a boom that falls short across a verge gives the builder something specific to fix. Include photos and measurements from the sites where the truck will work.
When ordering custom special-purpose trucks from China, use the same fleet brief for the chassis and body. A wheelbase affects where the equipment can sit, and a larger body adds weight before you load it. Ask for the proposed layout and axle loads early, while changing the configuration is still practical.
Scroll horizontally to view all columns.
| Working duty | Starting configuration | Evidence the quote should address |
|---|---|---|
| Frequent bin stops or container exchange | Refuse compactor or hook-lift garbage truck | Bin or container interface, loaded mass, route access and discharge space. |
| Sludge or liquid waste collection | Vacuum sewage suction truck | Waste type, hose route, useful capacity and disposal arrangement. |
| Roadside recovery or vehicle transfer | Flatbed or integrated wrecker | Target vehicle, loading geometry and the separate platform, winch or underlift ratings. |
| Streetlight, sign or building maintenance | Telescopic or articulating aerial work platform truck | Work point and approach path on the rated envelope, plus setup space. |
| Mobile water supply or foam response | Water tanker or foam fire truck | Refill and discharge duty, agent, crew equipment and completed-vehicle loads. |
Municipal collection starts at the bin or container
For frequent bin stops, check that a refuse compactor truck can lift the bins your crew already uses.
For container exchange, match the hook-lift garbage truck to the hook height, rail spacing and locking arrangement on your boxes. Check the lift rating against the heaviest loaded box and allow room to set it down at the site. Hook-lift garbage truck
Size a vacuum sewage suction truck around what the crew collects and where it can discharge. The Seychelles order used a 4,000 L tank and right-hand drive. For a similar order, confirm the destination steering requirement, hose access and loaded axle weights. Vacuum sewage suction truck ISUZU sewage suction truck shipped to Seychelles
Specify the deck, winch and cab around your recovery calls
Give the builder the weight and ground clearance of the vehicles you regularly collect. In the Dongfeng order for Peru, the flatbed had a 5 t platform and a winch rated for 4 t of pull. Put the two ratings on separate lines in a flatbed wrecker quote, alongside the usable deck size, loading geometry and restraints. Dongfeng tow truck shipped to Peru
If the recovery crew rides in the truck, check seating and tool storage. The double-cab ISUZU for Mongolia carried a 5,400 × 2,300 mm deck. If you lift and tow commercial vehicles, check the integrated wrecker underlift rating at the required reach and the resulting axle loads. ISUZU double-cab tow truck sent to Mongolia
Can the platform reach the work from where the truck can park?
Mark the parking position, work point and obstructions on a photo or site plan. Compare a telescopic boom for a direct approach with an articulating boom where the platform needs to pass around an obstacle. Ask for the applicable working envelope with the intended people and tools in the basket.
The HOWO order for Ethiopia specified a 20 m working height. When you quote a job like a streetlight across a verge, give the builder the horizontal offset and the ground area available for outriggers as well as the height. HOWO 20 m aerial work platform truck for Ethiopia
Give the fire-apparatus builder a response brief
Tell the water tanker fire truck builder how much water the crew needs to deliver and how it will refill the tank. Check that the proposed tank and pump leave room for the equipment and fit the road access and axle limits. Water tanker fire truck
For a foam fire truck, ask the fire service to specify the concentrate and proportioning rate, such as 3% or 6% where required for the chosen agent. Put the required flow at pressure, outlets and acceptance checks in the same brief. Foam fire truck
Price the work your receiving workshop will own
If you already have a chassis, ask about a custom truck body for export. The Mexico shipment included a complete ISUZU wrecker and two separate body packages. For a body-only quote, budget for a compatible chassis, installation, weighing and final checks. Name the workshop responsible for the completed truck. ISUZU wrecker and recovery bodies shipped to Mexico
Compare the delivered scope and the work the truck can complete in a shift. Include accessories, spares, transport, local installation and applicable destination charges. Use your fleet’s service and downtime records for operating costs. If a bigger body adds an extra turn restriction or makes the rear axle the limiting factor, price the configuration that can run the route.
Put the acceptance checks on the same sheet as the options
Before a custom truck chassis and body configuration goes into production, ask for a drawing and a revision-numbered equipment list. Put each acceptance check beside the requirement it verifies. The list can cover an existing bin fitting the lifter, the required platform position on the equipment chart or the agreed fire-pump test. Tie the records to the chassis and equipment identifiers when the unit is ready for inspection. Special-vehicle pre-delivery inspection checklist
Send the completed dimensions, weight, receiving location and intended delivery terms to the shipping team. Ask which records the forwarder needs and which documents the buyer needs for local registration. For a repeat order, use the approved first vehicle’s specification and list substitutions before production starts. KEEYAK shipping and delivery
- Destination, quantity, steering side and preferred chassis.
- Normal duty and heaviest or most restrictive working case.
- Photos and dimensions of the site or existing equipment interfaces.
- Complete truck or body package, with an agreed delivery point.
- Acceptance results, documentation and spares needed at handover.
Questions to answer before approving the build
Does body volume tell me the legal payload?
- Volume tells you how much space the body provides. Calculate loaded mass using the intended material and include the crew, fluids and equipment. Check gross vehicle mass and each axle load against the limits for the proposed truck and destination.
Can I specify right-hand drive or a different chassis?
- Send the destination and exact chassis or steering requirement. Confirm model availability, cab access, wheelbase and power take-off compatibility. Ask for loads and dimensions on the proposed completed build.
Can I inspect the factory or repeat a previous fleet order?
- Ask KEEYAK for a factory or video visit focused on the proposed body and assembly work. For a repeat order, provide the earlier order number and approved specification. Ask which components have changed and whether the same inspection checks still apply.
Which documents do I need for local registration?
- Ask your registration adviser about the completed vehicle, intended registration category and destination before approving the chassis. Agree who will provide each document and when. The shipping paperwork covers the shipment, while local acceptance requirements depend on the market.
Sources and applicability
Rated lifting capacity and compatible volume are separate catalog ranges. Check the loaded container against the offered chassis and hook system.
Sources checked:
Catalog configuration for compatible liquid waste and sludge, with equipment options confirmed per offer.
Sources checked:
Historic right-hand-drive ISUZU 4×2 order with a 4,000 L tank and a 3,360 mm wheelbase.
Sources checked:
Chassis and equipment specified for the shipment to Callao. The platform rating and winch traction rating describe separate equipment duties.
Sources checked:
Recorded cab layout, platform dimensions and chassis details for the overland shipment.
Sources checked:
Specified chassis and working height for the recorded order.
Sources checked:
Published water tank range. Pump duty and installed equipment are chosen for the agreed response role.
Sources checked:
Published water and concentrate capacities and listed proportioning options. Verify the actual agent, pump and configuration.
Sources checked:
Checks and documentation to agree for the completed vehicle.
Sources checked:
Shipment to Manzanillo and the specified platform on the complete truck. Local installation of the two body packages is outside this record.
Sources checked:
Transport methods and typical document responsibilities. Routing and the document package depend on the order and destination.
Sources checked:

